外文参考文献怎么提供给你啊，至少留个邮箱地址吧，如果需要回复邮箱地址即可，至于翻译得靠你自己了，希望能帮到你，多多给点悬赏分吧，急用的话请多选赏点分吧，这样更多的知友才会及时帮到你，我从文献资料中找也是很花时间的
已经把7篇关于汽车的外文文献发到你邮箱了，关键词为automobile，你里面选择对你最有帮助的来看吧，翻译成3000至4000汉字的应该完全不成问题。希望对你有帮助，也希望能满意。 有不明白地方还可随时再问我。 我邮箱：46******
On the improvement of the current status of urban bus transport Paper Keywords: organization; planning Abstract: Urban traffic system is the urban system is an important subsystem, the city depends on the survival and development of transport, the rapid development of urban traffic and promote development. The bus transport in urban traffic is an important part of the city, it should speed up the development of urban bus transport in order to promote the rapid development of cities. Passenger traffic from the city traffic can be classified as public transport and private transport system of the two. At present, China's urban public transport characteristics are: the city public transport lanes with low coverage and low levels due to management, and other vehicles occupied by frequent public transport bus lanes caused by the low operating efficiency. Urban road unreasonable, so that local public transportation system utilization rate. Aging of the city bus a high degree of scheduling and organization of the unreasonable. Should speed up the development of urban transport system, the full development of urban transportation convenient, fast, large capacity. Therefore the following aspects should be the improvement of the urban bus transportation available. 1 city bus transport lines Urban public transport routes should be in line the city's main traffic flow, public transport in cities should be divided into the main lines and feeder lines. The main line linking the main passenger terminal and transportation hub, more than millions of people in big cities, the focus on passenger traffic hub should be set up quickly direct public transport routes. Generally by means of surveys to obtain data on a straight-line access to integrated planning and overall planning should be coordinated with the City to carry out. The use of lanes, the best rationale for a dedicated lane so that other lane segregation, isolation can be used with dedicated lanes and is equipped with monitoring systems. 2 urban public traffic density lines Urban public transport motor vehicles are usually lines of planning density, in the city center 3 ~ 4km/km2, peri-urban areas of 2 ~ , the distance between the Route 600 ~ 1000m, walking no more than 4 ~ 6min appropriate, the Town urban bus to the length of line should be advised as to the length of 8 ~ 12km. Would cause long lines of passengers waiting a long time and bus time arrival rate of a series of drawbacks such as poor. 3 bus scheduling and organization Vehicle Scheduling optimization is to determine the normal and efficient public transport operation of the important factors. Changes based on passenger flow and the specific operating conditions and other regulations, various models of vehicles and road traffic organization, such as passenger flow during peak hours to focus on the trunk of the vehicle with high-capacity organizations Station or shuttle bus from the train, in the flow large and narrow streets, small turning radius and the flow concentration of the body block with short bus. In addition, they can employ intelligent management tool. For example: public transport vehicle automatic threshold control system (collectively referred to international AVMcautomatic vehicle monitoring system), it can dispatch room in between efficient information access, effective communication links between the two (GIS). The main vehicles used by the GPS scheduling, dynamic target tracking and data collection on traffic flow, GIS geographic information used in traffic management and visualization of dynamic traffic information display. In addition, you can use variable message board information, broadcasting, on-street public phone, public computer network terminal, which has been in the way of public transport users on the roadside, bus stations or bus stops and on the platform, access to real-time information on bus travel services. 4 Coordination of bus and taxi operations management Door-to-door taxi service for passengers with a higher level of public transport. Utilization rate of its high energy consumption and less than a bus, air pollution is serious, complete the volume occupied by units of time and space resources, such as road defects, it should be based on the level of urban development and the actual needs of the taxi industry to strengthen the management and operation management, so that the coordinated development of the bus. 5 vehicle technologies to improve China's passenger capacity by bus at a small (60-90 passenger), and medium-sized (90-130 passengers) and large articulated vehicles (130-180 passengers) should be based on actual passenger traffic to the deployment of appropriate models to resources to reduce the rate of empty vehicles. It shall also meet the passenger demand on the city bus traveling comfort and convenience of passengers getting on or off request. The development of an independent suspension type, dedicated low-floor bus chassis and city buses, so bus and channel height of the pedal in order to reduce the vehicle center of gravity high over the estate to the requirements of comfort. It should also be a timely replacement of vehicles, the general public the best service life of 5 to 6 years. Extended active duty bus noise, and exhaust, and mechanical failure more than a series of shortcomings, with the scientific and technological development, many countries have also developed a number of the outcome of the application of modern high-tech bus. For example: the invention of the next generation of Japan's "middle-distance inter-city bus transport system of unmanned." Germany developed a city with public passenger transport vehicles, new cars can be run along the fixed-line and the traditional advantages of the bus and tram combination. 6 Public Transport Priority Development Strategy Urban public transport as the road space point with the demand, low environmental pollution, energy consumption should be small, giving priority to the development of traffic, in addition to China's cities are mostly intensive, therefore, to public transport systems and other forms of secondary form of transport in our country the structure of urban passenger transport natural direction of development. Commonly used way of public transportation there are two types of priority: Set according to the actual situation dedicated bus lane or bus lane roads. Intersection of the first; junction bus priority measures on the main bus phase-specific, dedicated bus lane entrance, as well as other special bus priority measures in line with the movement. City bus transportation is the main urban transport system is to communicate all aspects of the social production of an important part of urban development is the decision an important foundation for the development of one, so to speed up the development of the city bus. 【【题目你可以翻译为论改善我国目前城市公共汽车交通现状，希望可以帮助你】】
邮件已发送，请及时查收。请及时采纳。
There will always be that when you own something when you do not think it would be valuable, but also do not see the value of it, but when you lose it when it come to repentance, but that at the moment when the lateness of the hour, too late for regrets and. I now have such a similar week-long automotive engine disassembly internship is over, memories of this time, he reluctantly are true. Wanted to be back in a week ago, then put in every day practice as seven hours to 27 hours use. This is true, this internship opportunities for me are too precious a this internship, I learned about auto engines knowledge, are ever at a lesson on what can not be compared. And I once again felt the profound theoretical and practical combination of the because of the arrangement to the engine of our components are Santana 2000 engine. First of all, for the automotive engine theory of knowledge, I understand that:Santana in Germany Volkswagen Ltd. 1982 products. The company entered Shanghai in 1983, to cooperate with the development of our country has been the development of three generations - four generations of production lines, and in 95 years will be Santana 2000 Electronic Fuel injection system into the main parameters of motor vehicles including technical parameters, the basic parameters, engine and chassis parameters parameters. Structure for the JV type engine, the combustion chamber for the ball flat, so that the function of strong squeezing gas area, to reduce fuel consumption and air pollution Valve for overhead camshaft type, camshaft push rod directly. Advantages of simple structure, the inertia of small parts, the system stiffness, and improve the effective engine speed. Valve for the hydraulic rod to mention, the automatic adjustment of valve clearance. Intake system has electric heaters and temperature control the intake valve, you can ensure that a smooth start and shorten the warm-up time. Closed water cooling system uses forced basic structure of the modern automobile engine from crank linkage, valve body, transmission system, lubrication system, cooling system, ignition system, start the Department of the composition. Linkage crank engines are energy conversion and transmission of power institutions. Valve bodies are engines of ventilators, ventilation process: on time and turn off the control valve to ensure full combustion gas mixed with gas and emissions. Supply lines are guaranteed to give a total cylinder fresh combustible mixture and export emissions, and in accordance with the different engine operating conditions the supply of different quantity and concentration of combustible gas mixture.中文翻译如下：人们总说，当你拥有一样东西的时候，你会不觉得的它的珍贵，也看不到它的价值所在，但是当你失去它的时候才恍然悔悟，此刻却以为时已晚，后悔莫及。我现在就有这么一种类似的感受。为期一周的汽车发动机拆装实习结束了，回忆这段时光，竟真的是恋恋不舍。恨不得能回到一周前，然后把每天实习的7个小时当成27个小时来用。确实如此，这次实习的机会对我来说真的是太珍贵了。在这次实习中，我学习到的关于汽车发动机的知识，是在以往任何一节课上都不能所比拟的。而我也再一次深刻感受到了理论和实践结合的必要性。由于老师的安排，我们组分到的发动机是桑塔纳2000型发动机。首先，对于汽车发动机理论知识的学习，我了解到：桑塔纳轿车是德国大众汽车有限公司1982年的产品。该公司于1983年进入上海，同我国进行合作开发，目前已发展为三代-四代生产线，并于95年将桑塔纳2000电控汽油喷射系统投入市场。汽车的主要参数包括技术参数、基本参数、发动机参数和底盘 参数。 发动机结构为JV型，燃烧室为扁球形，这样可以则功能强挤气面积，减低油耗和大气污染配气机构凸轮轴为顶置式，凸轮轴直接推动连杆。优点为结构简单、零件惯性小、系统刚度大、有效提高发动机转速。气门提杆为液压式，气门间隙自动调节。进气系统有电加热器和温度控制进气阀，可以确保汽车顺利启动和缩短暖机时间。冷却系统采用闭式水冷强制循环。现代汽车发动机基本结构由曲柄连杆机构、配气机构、传动系、润滑系、冷却系、点火系、启动系组成。曲柄连杆机构是发动机进行能量转换和传递动力的机构。配气机构是发动机的换气机构，换气过程：控制气门按时关闭，保证气配时充分燃烧混合气和排放废气。供给系是保证向气缸共给新鲜可燃混合气和导出废气，并按照发动机不同工况供给不同数量和浓度的可燃混合气。这篇挺好的啊，嘻嘻
There will always be that when you own something when you do not think it would be valuable, but also do not see the value of it, but when you lose it when it come to repentance, but that at the moment when the lateness of the hour, too late for regrets and. I now have such a similar feel. A week-long automotive engine disassembly internship is over, memories of this time, he reluctantly are true. Wanted to be back in a week ago, then put in every day practice as seven hours to 27 hours use. This is true, this internship opportunities for me are too precious a true. In this internship, I learned about auto engines knowledge, are ever at a lesson on what can not be compared. And I once again felt the profound theoretical and practical combination of the need. Teacher because of the arrangement to the engine of our components are Santana 2000 engine. First of all, for the automotive engine theory of knowledge, I understand that: Santana in Germany Volkswagen Ltd. 1982 products. The company entered Shanghai in 1983, to cooperate with the development of our country has been the development of three generations - four generations of production lines, and in 95 years will be Santana 2000 Electronic Fuel injection system into the market. The main parameters of motor vehicles including technical parameters, the basic parameters, engine and chassis parameters parameters. Structure for the JV type engine, the combustion chamber for the ball flat, so that the function of strong squeezing gas area, to reduce fuel consumption and air pollution Valve for overhead camshaft type, camshaft push rod directly. Advantages of simple structure, the inertia of small parts, the system stiffness, and improve the effective engine speed. Valve for the hydraulic rod to mention, the automatic
还是找个英语老师帮翻译一下吧，别人翻译的你未必好用，如果你不懂英语，这是专业，错了不好
The society entered the information network time, the people no longer satisfy to the automobile request one kind of riding instead of walking tool, hoped the automobile is the life and the operating region one kind extends, on automobile on elephant in own office and family same work and the same time, the automobile computerization also day by day rapidly develops, was considered is in an automobile technological development advancement revolution, the automobile computerization degree is weighs by regarding as the modern automobile level the important along with the computer technology, the communication technology, the integrated circuit technology rapid development, take the numeral field bus as representative's scene measuring appliance, the equipment massive applications, a tedious scene segment bed sheet succinct field bus network replaces, the signaling quality also greatly enhances, the automobile also starts to march into the network time. In the near ten years, the user regarding automobile comfortableness, the security as well as the environmental protection and so on each performance request enhances order to meet the need which these increase day by day, on the automobile the computer controls the electronic electric appliance equipment sharp growth, causes the automobile (is specially passenger vehicle) designs the electric appliance line arrangement to be more and more addition, because because on the automobile each kind of electronic electric appliance meets the point insertion quantity along with it sharp increase, in the automobile travel process meets the point insertion the breakdown to create on the automobile the electronic electric appliance equipment malfunction question to be more and more order to solve the above problem, very many new vehicle types (are specially upscale vehicle type) in the development starts widely to apply the computer network article introduced the computer network technology in the automobile the application basic principle, elaborated the networking in the automobile interior and exterior application situation, introduced the automobile interior network characteristic and the automobile interior network standard, with emphasis narrated the control confined network CAN principal characteristic and the application. According to the automobile driving quality function influence division, may the automobile electronic products induction be two kinds: One kind is the automobile electronic control, including engine, chassis, automobile body electronic kind is the vehicle carries the automobile electronic installation, including the automobile information system, the guidance system, the automobile sound and the television entertainment system, the vehicle carries the communications system, the surfer equipment and so : automotive, computer networks, local area network control, network standards
附录对论文来说主要是一个补充说明作用，附录属于正文，需要使用时才会写，一般情况是不需要写的。附录是放在正文末尾部分，是正文中不便于放置的一些资料。为了保证引用资料的权威性和完整性，所以才将附录放在论文末尾的，加上标号，可以在原文出现的地方找到它，并在原文中写：“XXX详见附录1”。一、附录写作要点：1、正文中长公式的推导和证明可依次在附录中给出。2、与论文关系密切的不是作者自己的分析证明、工具和表格等。3、未列入正文的实验数据。在毕业论文结束时，学习期间发表的论文、专利、获奖和社会评价应附上学生本人在学习期间发表的论文、获得的专利、获奖、评价和社会评价以及项目实现的相关材料（通常只能写一份目录清单）。4、论文中的附录是提供您在论文中使用的相关原始资料。这通常是因为在论文中无法显示或不恰当地呈现的内容，例如问卷中使用的标题有些时候是为了保护版权，只呈现一部分材料。5、并非所有的东西都会放在毕业论文的附录中。二、毕业论文附录的格式要求1、附录格式要求“附录”一词用黑体三号居中打印。两个字的中间空一格，下面需要空一行写附录的标题（黑体四号居中打印），下面空一行是附录内容（使用宋体小四号） 。如果有多个附录，则可按附录1，附录2，附录3的顺序编号......与上述格式类似2、附录撰写要求对于一些不适合放在正文中但是又具有参考价值的内容，可写入附录中，附录是可选项目。附录大致包括以下材料：1、比正文更详细的理论基础、研究方法和技术要点、可阅读的参考文献的标题、理解文本内容的有用补充信息等；2、太长的材料不包括在正文中；3、一些重要的原始材料。数据、公式推导、软件源程序、框图、结构图、统计表、计算机打印输出、照片、电路图等。
附录对论文来讲主要起到补充说明的作用，附属于正文，必要时才添加，一般情况是省略掉的，把原文中要说明的相关材料。最好是整理成表格放到论文的最后，并且标上标号，要把它在原文出现的地方找到，在原文中写。
附录的内容包括:
(1)正文中过长的公式推导与证明过程可以附录中依次给出。
(2)与本文紧密相关的非作者自己的分析，证明及工具用表格等。
(3)在正文中无法列出的实验数据。在校学习期间所发表的论文、专利、获奖及社会评价等在毕业论文的最后，应附上学员本人在校学习期间所发表的论文，获得的专利，获奖、鉴定及工程实现的社会评价及有关资料(一般只写目录清单即可)。
附录写作要点：
1、正文中长公式的推导和证明可依次在附录中给出。
2、与论文关系密切的不是作者自己的分析证明、工具和表格等。
3、未列入正文的实验数据。在毕业论文结束时，学习期间发表的论文、专利、获奖和社会评价应附上学生本人在学习期间发表的论文、获得的专利、获奖、评价和社会评价以及项目实现的相关材料（通常只能写一份目录清单）。
4、论文中的附录是提供您在论文中使用的相关原始资料。这通常是因为在论文中无法显示或不恰当地呈现的内容，例如问卷中使用的标题有些时候是为了保护版权，只呈现一部分材料。
5、并非所有的东西都会放在毕业论文的附录中。
前言翻译。论文附录译文写的内容诗论文前言，讲论文前言转换成英文之后，附录在上面即可。毕业论文是专科及以上学历教育为对本专业学生集中进行科学研究训练而要求学生在毕业前撰写的论文。
问题一：见附录用英文怎么说 Refer to appendix. 如果多骇一个附录那么就是Appendix A, B, C... 问题二：毕业论文附录的英文原文，英文翻译是什么意思？ 20分 先到百度文库，找一篇此类文档中文的，然后用有道翻译，或是谷歌在线翻译翻成英 文，然后把英文放上面，中文放下面。希望可以帮到你。如果要找标准的PDF格式外文文 献，可以在谷歌，用英文文献名+空格+PDF 这样比较容易找到。 第一是Google搜索，主要是英文，尤其是其学术搜索，意义大。 第二，通过各大学图书馆系统，进入几个主流的出版发行集团。 第三，利用网络免费储存、电子书系统。尤其是国外多。 1、论文题目：要求准确、简练、醒目、新颖。 2、目录：目录是论文中主要段落的简表。（短篇论文不必列目录） 3、提要：是文章主要内容的摘录，要求短、精、完整。字数少可几十字，多不超过三百字为宜。 4、关键词或主题词：关键词是从论文的题名、提要和正文中选取出来的，是对表述论文的中心内容有实质意义的词汇。关键词是用作机系统标引论文内容特征的词语，便于信息系统汇集，以供读者检索。 每篇论文一般选取3-8个词汇作为关键词，另起一行，排在“提要”的左下方。主题词是经过规范化的词，在确定主题词时，要对论文进行主题，依照标引和组配规则转换成主题词表中的规范词语。 5、论文正文：（1）引言：引言又称前言、序言和导言，用在论文的开头。 引言一般要概括地写出作者意图，说明选题的目的和意义, 并指出论文写作的范围。引言要短小精悍、紧扣主题。〈2）论文正文：正文是论文的主体，正文应包括论点、论据、 论证过程和结论。主体部分包括以下内容：a.提出-论点；b.分析问题-论据和论证；c.解决问题-论证与步骤；d.结论。 6、一篇论文的参考文献是将论文在和写作中可参考或引证的主要文献资料，列于论文的末尾。参考文献应另起一页，标注方式按《GB7714-87文后参考文献著录规则》进行。中文：标题--作者--出版物信息（版地、版者、版期）：作者--标题--出版物信息所列参考文献的要求是：（1）所列参考文献应是正式出版物，以便读者考证。（2）所列举的参考文献要标明序号、著作或文章的标题、作者、出版物信息。 一，选题要新颖。 这次我的论文的成功，和高分，得到导师的赞许，都是因为我论文的选题新颖所给我带来的好处。最好涉及护理新领域，以及新进展，这样会给人耳目一新的感觉。 二，大量文献做基础 仔细查阅和你论文题目和研究范围相关的文献，大量的文献查阅会你的论文写作铺垫，借鉴别人的思路，和好的语言。而且在写作过程不会觉得语言平乏，当然也要自己一定的语言功底做基矗 三，一气呵成 做好充分的准备，不要每天写一些，每天改一些，这样会打断自己的思路，影响文章的连贯。 四，尽量采用多的专业术语 可能口语化的表达会给人带来亲切感，但论文是比较专业的形式，是有可能做为文献来查阅和检索的，所以论文语言的专业化，术语化会提升自己论文的水平。 五，用正规格式书写 参考正规的论文文献，论文格式。不要因为格式问题，而影响到你论文的质量。 六，最好在计算机上完成写作过程 如果有条件最好利用电脑来完成写作过程，好处以下几点：1，节省时间，无论打字的速度慢到什么程度，肯定要比手写的快。2，方便，大量的文献放在手边，一个一个查阅是很不方便的，文献都是用数据库编辑，所以都是在电脑上完成。提前先在电脑上摘要出重点，写出提纲，随时翻阅，方便写作。3，修改编辑，在电脑随时对文章进行修改编辑都是非常的方便。4，随时存档，写一段，存一段，防止突然停电，或者电脑当机。本人就是吃了这个大亏，一个晚上的......>> 问题三：英语高手帮忙翻译一个词语 附录--Appendices 没有简写 问题四：论文的附录（英文原文+译文）要写多少字？ SFWE 根据我搜集的一些网站来看，建议看看这个，要做毕业论文以及毕业设计的，推 荐一个网站 lw54 ，里面的毕业设计什么的全是优秀的，因为精 挑细选的，网上很少有，都是相当不错的毕业论文和毕业设计，对毕业论文的写 作有很大的参考价值，希望对你有所帮助。 别的相关范文很多的，推荐一些比较好的范文写作网站，希望对你有帮助，这些 精选的范文网站，里面有大量的范文，也有各种文章写作方法，注意事项，应该 有适合你的，自己动手找一下，可不要照搬啊，参考一下，用自己的语言写出来 那才是自己的。 如果你不是校园网的话，请在下面的网站找： 毕业论文网： wsdxs 分类很细 栏目很多 毕业论文： lw54 毕业设计： wsdxs/html/sf/lw/2009/0928/146347 开题报告： wsdxs/html/lunwenzhidao/kaitibaogao 实习论文： wsdxs/html/shixi 写作指导： wsdxs/html/lunwenzhidao 问题五：英语论文中附录怎么标注 能更具体些么？ 你指的是appendix？ 问题六：规范性附录 英文怎么说？ 5分 “规范性附录”英语是“Normative appendix” “规范性”是：Normative Appendix是“附录” 非规范性(non-normat丹ve) ：）~ 问题七：陈春娥英文怎么翻译？ Chen Chune第一种方法是：起一个与中文名字“谐音”的英文名字。比如李梅，可以起May Li，“梅”与May正好谐音。下面是四个例子，您可以参考。许多《英汉词典》的附录部分，都有英文名字的列表，您可以根据您的名字的汉语发音，找一个大致“谐音”的英文名字。不过这种方法有很大的局限性，大多数中文名字都没有谐音的英文名字，所以我们只能考虑另外两种方法。 问题八：针灸减肥真的有用吗？ 我亲身经历过，自己的配合也是减肥成功的50%的因素，因为大家都知道中医是一个很神奇的东西，针灸减肥配合美饥院对你制定的食谱这样才能起到最佳的效果。制定食谱并不是说控制饮食的目的，而是类似化学效应的一种效应（我比较笨，想不出别的比喻，可能不太恰当）针灸的方法+所食用的东西=脂肪的代谢与排出，所以就减肥成功了，而且不仅仅是体重还有尺寸可以让你看得到的。我减掉了30斤，原来可是130斤哦。当然，任何想减肥的人都需要不能暴饮暴食的，因为正是因为我们没有良好的饮食习惯所以我们原来才胖的呀：）所以，我认为，针灸减肥真的有用哦，我相信。
查到10篇关于电动车的文献。我想能适合楼主的可能有个一篇两篇吧。如果楼主感兴趣，可以发邮件到，我发给你全文。[1]O'Keefe, M., K. Bennion, and . Laboratory, Comparison of Hybrid Electric Vehicle Power Electronics Cooling Options. 2008: National Renewable Energy Laboratory.[2]Shabashevich, A., et al., Consumer Ready Plug-in Hybrid Electric Vehicle. Team-Fate, University of California, Davis. http://www. teamfate. net/technical/UCDavis_Spring2007_TechReport. pdf, 2007.[3]Rousseau, A., S. Pagerit, and D. Gao. Plug-in Hybrid Electric Vehicle Control Strategy Parameter Optimization. 2007.[4]Syed, F., et al., Derivation and Experimental Validation of a Power-Split Hybrid Electric Vehicle Model. IEEE TRANSACTIONS ON VEHICULAR TECHNOLOGY, 2006. 55(6): p. 1731.[5]Moreno, J., M. Ortúzar, and J. Dixon, Energy-Management System for a Hybrid Electric Vehicle, Using Ultracapacitors and Neural Networks. IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, 2006. 53(2).[6]Miller, J., Hybrid Electric Vehicle Propulsion System Architectures of the e-CVT Type. IEEE Transactions on Power Electronics, 2006. 21(3): p. 756-767.[7]Markel, T. and A. Simpson. Plug-In Hybrid Electric Vehicle Energy Storage System Design. 2006.[8]Wang, C., O. Stielau, and G. Covic, Design considerations for a contactless electric vehicle battery charger. Industrial Electronics, IEEE Transactions on, 2005. 52(5): p. 1308-1314.[9]Musardo, C., et al. A-ECMS: An Adaptive Algorithm for Hybrid Electric Vehicle Energy Management. 2005: IEEE; 1998.[10]Faiz, J., et al., Sensorless direct torque control of induction motors used in electric vehicle. Energy Conversion, IEEE Transactions on, 2003. 18(1): p. 1-10.
Along with the development of science and technology, intelligent and automation technology is more and more popular, all kinds of hi-tech also widely used in intelligent robot toy car and manufacturing field, make intelligent robot more and more diverse. Intelligent car is a variety of high-paying technology integration body, it incorporates mechanical, electronic, sensors, computer hardware, software, artificial intelligence and many other subject knowledge, can involves many of today's current areas of technology. This car design mainly by the single chip microcomputer control system module, manostat module, motor driver module, infrared inspection module and to the wireless digital module composition, system to C8051F340 microcontroller as the core, set to foreign control, use linear regulator chip to voltage stability of control for single chip microcomputer and other peripherals for the reliable power supply, using infrared to the module black and white signal detection, use L298N motor driver module to the dc speed-down motor stability control, use light coupling strength chips for electrical isolation of control, disappear
Along with the development of science and technology, intelligent and automation technology is more and more popular, all kinds of hi-tech also widely used in intelligent robot toy car and manufacturing field, make intelligent robot more and more diverse. Intelligent car is a variety of high-paying technology integration body, it incorporates mechanical, electronic, sensors, computer hardware, software, artificial intelligence and many other subject knowledge, can involves many of today's current areas of technology. This car design mainly by the single chip microcomputer control system module, manostat module, motor driver module, infrared inspection module and to the wireless digital module composition, system to C8051F340 microcontroller as the core, set to foreign control, use linear regulator chip to voltage stability of control for single chip microcomputer and other peripherals for the reliable power supply, using infrared to the module black and white signal detection, use L298N motor driver module to the dc speed-down motor stability control, use light coupling strength chips for electrical isolation of control, eliminate interference, the use of wireless digital module CC1101 for two car communication. The intelligent design two cars are from the start to car, overtaking alternately lead, lead a circle overtaking about 27 seconds. Key words: C8051F340 infrared to the dc speed-down wireless digital overtaking lead
Cars in America(美国的汽车)Cars in AmericaCars are an important part of lifein the United States. The car made the UnitedStatesanationon helped to make the United States what it is are three main reasons why the car became so popular in the United States. First of all the country is a huge one and Americans like to move around in it. The cars provide the most comfortable and cheapest form of second reason that cars are popular is the fact that the United States never really developed an efficient and inexpensive form of public transportation. Long-distance trains have never been as common in the United States as they are in other parts of the world. Nowadays there is a good system of air service provided by planes. But it is too expensive to be used third reason is the most important one, though. The American spirit of independence is what really made cars popular. Americans don't like to wait for a bus, or a train or even a plane. They don't like to have to follow an exact the freedom a car gives them is what Americans want most to decrease of gas supplies has caused a big problem for Americans. But the answer will not be a bigger system of public transportation. The real solution will have to be a new kind of car, one that does not use so much gas.美国的汽车汽车是美国生活的重要组成部分。汽车使得美国成为轮子上的国家，它也帮助美国成为现在的样子。汽车在美国如此盛行有三个主要原因。首先这个国家地域辽阔，而美国人喜欢在其间来回走动。汽车提供了最舒适最便宜的交通方式。汽车如此盛行的第二个原因是美国从未真正发展过有效廉价的公共交通这一事实。美国的长途火车从未像世界上其它地方那么普及。如今飞机提供了空中服务的良好体系。但是飞机太贵了，不能频繁使用。而第三个原因是最为重要的。美国人的独立精神是使得汽车盛行的真正原因。美国人不喜欢等公共汽车、火车甚至飞机。他们不喜欢必须遵循精确的时间表。汽车给予他们的自由正是美国人最想得到的。汽油供给的减少已经给美国人带来了巨大的问题。但答案不是发展更大型的公交体系。真正的解决方式必须是一种新型的汽车，那种不需要使用很多燃料的汽车。Car PollutionEach year there is an increasing number of cars on the roads as millions of new cars are produced. One out of six Americans works at making cars, driving trucks, building roads or filling up gas. Americans couldn't live without cars!Most Americans would find it hard to imagine life without a car. However, some have realized the serious problem of air pollution caused by cars. The polluted air becomes poisonous and dangerous to way to get rid of the polluted air is to make a car without pollution. But to build a clean car is easier said than done. Progress in this field is way is to replace car engines with something else. Inventors are now working on steam cars as well as electric cars. Many makers believe that it will take years to develop a practical model for prevent the world from being polluted by cars, we have to make some changes in our lives. Americans, for example, have to cut down on the number of their total are encouraged to use bicycles, which are thought to help keep the air this change does not come easily. A large number of workers may find themselves without jobs if a car factory cioses down. Thus the problem of air pollution would become less important than that of unemployment. Although cars have led us to a better life, they have also brought us new problems.汽车污染上路的汽车数量逐年增长，同时，每年都会生产出几百万辆新车。在美国，每六个人中就有一个从事与汽车相关的工作：造车、开车、修路、加油等等。离开汽车，美国人无法生活!大部分美国人简直无法想象没有车的生活会是什么样子。但是一些人也已经意识到汽车造成的空气污染已成为严重的问题。被污染的空气具有毒性，并且危害健康。解决空气污染的方法之一就是制造无污染汽车。但是生产清洁汽车说来容易做来难。目前，这一领域的进展十分缓慢。另一个方法就是使用其他东西替代汽车发动机。发明家正在研制蒸汽汽车和电车。但是许多厂家认为我们可以使用的实用型汽车的诞生可能还需要几年时间。要想阻止全球化的汽车污染，我们需要对自己的生活方式做出适当的改变。例如，在美国，需要缩减汽车总量。鼓励人们使用有助空气清洁的自行车。但这种改变不能一蹴而就。一旦汽车工厂关闭，就会有大量工人失去工作。与失业相比，空气污染似乎就不再那么重要了。尽管汽车为我们带来了更加舒适的生活，同时，它也带来了新的问题。
CAN bus in the electric vehicle monitoring system of Abstract Now, CAN, high-performance and reliability has been recognized and was widely used in industrial automation, marine, medical equipment, industrial equipment, and so on. Field Bus is the development of automation technology One of the focuses of the area known as automated computer LAN. It is a distributed control system to achieve real-time between the nodes, reliable data communications providing strong technical support. CAN bus belonging to the scene of the areas, it is an effective support for real-time control of distributed control or serial communication network. Compared with many of the current RS-485 based on the R line Construction of the Distributed Control System, based on the CAN bus distributed control system has obvious advantages. In this paper, occupies a lot of relevant information based on the comprehensive use of various methods of the CAN bus in the electric vehicle monitoring system in the application of theory and an analysis of development issues, and some of the problems raised his own views. The full text is divided into four parts: The first part of the main topics on the background and content of the subjects studied in the context of topics to write on the CAN bus status and significance in the research described in the content of the object of measurement requirements and complete the task of this paper. The second part, write data acquisition module design, from the SJA1000 CAN-based communications port design, acquisition, the electric car design; electric car design capacity of the collection node consists of three parts. The third part, mainly to write the electric vehicle monitoring network design, the first Fieldbus awakened comparison and choice, selected after the introduction of the CAN bus, the last of the SJA1000 CAN bus controller is introduced. The fourth part is really on the reliability of the system design for discussion, data from the calibration, the anti-jamming software and hardware design of the anti-jamming design in three areas to address the reliability of the system problems. Key words :Fieldbus; CAN bus; SJA1000; nodes;
Analyse der Entwicklungsgeschichte der Automobilindustrie Deutschlands反正我们的论文题目就是这样的，要么就用Analyse，要么就干脆不用。我自己的论文题目就是：Einfluss der Umweltfaktors auf Menschen-Ueber Stefan Zweigs Novelle Schachnovelle.我就懒得用Analyse，也是可以的。楼上的翻译掉了一点，发展史是Entwicklungsgeschichte
1.采用SCR后处理技术降低车用柴油机排放 Adopting SCR Post-processing Technique to Lower Discharge of Vehicular Diesel Engine 2.论柴油车的节能与环保优势 On Energy-saving and Environmental Protection of Diesel Vehicles
标题：CAN BUS used in the monitoring system of the electric vehicle