光学零件研究报告.武汉职业技术学院课程论文光学零件研究报告系别:电子信息工程学院班级:光电08302学号:作者:王玉朝指导教师:2010年月日7、开球面机械化铣磨球面方法型料毛坯上刚性盘,在专用球面铣磨机上以范成性法成型球面。.Sina...
光学零件工艺学(论文资料),光学零件工艺手册,光学零件制造工艺,光学零件工艺手册pdf,轴类零件工艺论文,光学零件表面疵病,光学零件图纸,光学零件,光学零件技术,光学零件图
精密与特种结课论文.doc.112080201021指导教师:摘要:主要论述对精密与特种这门课学习后的一些情况所得,并结合所查资料对精密与特种发展与运用方面有所阐述。.关键字:精密;特种;电火花;电化学;离子束;超声...
第2章工艺方案分析2.1零件图图1-2典型轴类零件图2.2零件图分析2.3确定方法方法的选择原则是保证表面的精度和表面粗糙度的要求。由于获得同一级精度及表面粗糙度的方法一般有许多,因而在实际选择时,要结合零件的形状、尺寸大小和形位公差要求等全面考虑。
10.期刊论文罗松保.张建明非球面曲面光学零件超精密装备与技术-光学精密工程2003,11(1)"Nanosys-300非球面曲面超精密复合系统"是"九五"重点预研课题-"非球面曲面的超精密与测量技术"的主要研究成果.重点对非球面曲面光学零件超精密
因此,不仅加快了单块光学零件的速度,而且还节省了装配、校正和定心等辅助时间。论—20世纪光学零件技术发展的回顾最初,用金刚石车削的标卖内存在着肉眼看得见的印迹,所以只能用在远红外波长(8~12μm)。
第一篇光学零件类型及图面技术要求.第二篇光学零件的基本工艺光学零件的基本工艺是指一般的光学零件在过程中都需要经过的工艺,针对我公司而言也就是说包括铣磨、精磨、抛光、清洗、磨边、镀膜、胶合等工序工艺。.第一章光学零件类型及技术...
随着先进的光学技术的不断更新,越来越多的光学技术人员发表了专业的光学技术论文。本文带您看2012年OFweek光学网十大技术论文:一、光学零件主要难点的分析本文根据光学零件在当今科学技术中的重要作用,阐述了球面及非球面光学
内容提示:河南工业职业技术学院HenanPolytechnicInstitute毕业设计题目光学零件的系别光电工程系专业精密机械技术班级精密机械1002班姓...
光学零件毕业设计.doc,河南工业职业技术学院毕业设计PAGEPAGE26摘要在光学工艺中,采用固着的金刚石磨具玻璃,是提高生产效率最有效的方法。用...
内容提示:第32卷增刊2006年8月光学技术0门ICALTECHNIQUEV01.32Suppl.August2006文章编号:1002。1582(2006)S-0410-05光学零件主要难点的分析+王鹤岩1...
综上分析可知,光学零件难点主要在于保证高精度面形的同时要保证高质量的表面质量,而产生这种难点的根本原因在于至今所有的球面和非球面零件的均不是依据...
关键词:光学零件研磨抛光磨削金刚石磨床作者:辛企明作者单位:北京理工大学光电工程系母体文献:展望21世纪初光电技术发展趋势研讨会论文集...
随着光学零件在前沿技术中的广泛应用,超光滑表面技术已经成为当前研究的热点.文章阐述了超光滑表面的定义特点及机理,重点介绍目前国内常用的古典法抛光技术,...
论文信息参考文献被引情况PDF全文分享:摘要一般将厚度与长度(或直径)的比值小于1:10的光学零件称为薄型光学零件,有时可达到1:40以上,所以薄型零件的难点是...