电力英语翻译研究论文

Do not cut power belt load replacement high pressure isolator operating method research Abstract: High pressure isolator in the 10kV distribution network indispensable, mainly installs in distribution line's contact point, the partition place, the branch line and so on place, forms the obvious cut-off point in the electric circuit, and participates in the change movement way massively the floodgate operation but actually, therefore presents like this such breakdown unavoidably. Because the live-wire work may create the huge economic efficiency and the social efficiency, therefore in has under the live-wire work premise to be possible to adopt charged processing this kind of breakdown generally, the work method may adopt the belt load or the idling carries on replaces two ways, but considered in reality isolator's damaged condition (sometimes causes isolator to be unable the loss which separation) and the power cut creates, the main method needs to adopt the belt load replacement isolator. Key words: High pressure isolator; Belt load; Replacement

This paper first book according to the mission to system and routes and all load parameter, this paper analyses load development trend. Consult the relevant information design first, collection and research a lot of material, and translate the related foreign material, then analyzed to load, precise calculation and analysis of load growth from the necessity of clarified, then through wipeout of substation of generalization and built to qualify to consider, and through the direction of load data analysis, safety, economy and reliability into consideration, determine the 35kV voltage level 110 kv and worked two approach compared with cable connections to determine the Lord in ways that do the Lord wiring system design, 110 kv side chose to expand inside bridge connection mode, the consumers 10KV single busbar subsection wiring way, then tong ?

This paper first book according to the mission to system and routes and all load parameter, this paper analyses load development trend. Consult the relevant information design first, collection and research a lot of material, and translate the related foreign material, then analyzed to load, precise calculation and analysis of load growth from the necessity of clarified, then through wipeout of substation of generalization and built to qualify to consider, and through the direction of load data analysis, safety, economy and reliability into consideration, determine the 35kV voltage level 110 kv and worked two approach compared with cable connections to determine the Lord in ways that do the Lord wiring system design, 110 kv side chose to expand inside bridge connection mode, the consumers 10KV single busbar subsection wiring way, then through the load calculation and power supply range identified the main transformer sets, capacity and model, with three, determine the transformer capacity as the 50000KVA, SZ10-50000 / type, then the standard 110 to short-circuit calculation method of what value is analyzed and processing. According to the maximum continuous working current and short circuit calculation results of calculation of isolating switch, bus, voltage transformer, current transformer and the selection. On the main transformer in setting calculation and analysis of the lightning part, determine the calculation and analysis, the method, and lightning made corresponding principle diagram. Thus finished 110 kv substations electrical parts of the consumers 10KV/design. 满意不?

Do not replace the high-voltage electricity load isolation method of switching operationsAbstract: High-pressure isolation switch in the 10 kV distribution network in the essential, the main power distribution lines installed in the focal point, Sub-Department, the branch lines, etc., in a clear disconnect the circuit, and heavily involved in the operation to change the way inverted Gateway operation, so inevitable that this or that kind of failure. As Charged operations can create enormous economic and social benefits, so charged with operating under the premise of general charged can be taken to deal with such failure, the method of operation can be taken on-load or no load to be replaced in two ways, but in practice Disconnectors consider the extent of damage (sometimes lead to isolation switch can not be disconnected) and the losses caused by power failure, the main method is to take load isolation switch words: high-pressure isolation switch;-load; replacement

Title:Function Analysis based on the Transformers of Infrared Measuring TemperatureAbstract:Aiming to the traditional handy infrared equipment of measuring temperature used to transformers can't satisfy the requests of intelligent transformers and electricity system a maintenance and monitoring of trasformers' function status. We bring up a system based on the infrared measuring temperature system. Finally it proves that this system can monitor the transformers' function status remotely and analyze the function status by the temperature data and photographs.