澳洲期刊投稿要求什么

期刊论文投稿有两部分工作，我们需要提高注意：其一，是如何进行投稿期刊的选择，合适对口的期刊选择，可以提高投稿的命中率，大大减少投稿周期；其二，如何根据投稿须知把文章的格式进行相应的调整，不少论文是因为格式审查不过关，要么直接被拒稿，要么进行一次次返修，在这个过程中耽误了不少时间，十分不值得。补充期刊论文图表格式要求,如下图：

1.期刊投稿一般是要给期刊发每位作者的照片和对应作者的简介的。2. 投稿论文时是需要填写关于作者的个人信息的,方便编辑和作者联系,在投稿的时候要看所投的稿件是怎么规定的。3. 阅读并遵守期刊的投稿须知非常重要。每个期刊都会针对各类文章提出详细的投稿要求，包括字数、作者数量、图表、作者的经济利益披露、剽窃、代写等。遵守投稿须知，论文不一定会被接收，但不遵守一定会被拒稿。

Short Communications (Letters) are intended as brief reports of significant, original and timely research results on the science, applications and processing of materials which warrant rapidpublication. In considering a manuscript for publication, particular attention will be given to the originality of the research, the desirability of speedy publication, the clarity of the presentation andthe validity of the conclusions. There is a strict four-page limit to printed articles. Manuscriptsmust not exceed 2000 words plus three figures and one table. This includes everything: the title,authors, affiliations, abstract, keywords, body of the manuscript, acknowledgements, references,figure captions, etc. The maximum number of figures is strictly limited to five. If the maximum of4 figures is used, then the total number of words must be reduced to 1800. If the maximum of 5figures is used, then the total number of words must be reduced to 1600. If more than 5 figures areused, the manuscript will be rejected. The manuscript submitted for review should not exceed8 pages (including title, abstract, references, figures, tables and figure captions). ShortCommunications need to report a concise but exhaustive Material and methods section included inthe main text.

1、引用文献不要超过10篇吧，文献内没有文章名，有个materials letters的投稿模板。

2、文献图片要少，5 figure字数<1600； 4 figure字数<1800。

3、其次就是文章内容上了吧，比如introduction，不要扩太多了，method部分，简单扼要。

4、Materials Letters投稿格式要正规。

MATERIALS LETTERS

sciencedirect.com/science/journal/0167577X

ees.elsevier.com/mlblue/

ELSEVIER SCIENCE BV， PO BOX 211，AMSTERDAM，NETHERLANDS，1000 AE

工程技术-材料科学

NETHERLANDS

Semimonthly

(说明:本文以接收,格式审查不存在问题；abcdefg代替为文章具体内容)

abcdefg-------（文章题目）

作者1a， b、作者2a， b、作者3a，b、*（作者）

a、College --------, ---- University, city, 066---, China

b、--------, --- University,city, 066---, China

c、-------,---- Road,----, -----,45678,USA

* Corresponding author: Tel.:+86-1234-0123456; E-mail:

Abstract:In this paper, the ----- of -------------abcdefg

Keyword: Micro----; -------；------；------；------

1、Introduction

The precipitation hardening ---------alloys are extensively used in the ------- structural material. -----------abcdefg

abcdefg--------------abcdefg

abcdefg--------------abcdefg

2、 Materials and methods

The composition of the experimental ----------abcdefg

Vickers microhardness was ---------abcdefg

Fig. 1

3、 Results and discussions

After -------------------abcdefg

Fig. 2

The ----------------abcdefg

A comparison -----------abcdefg

Fig. 3

abcdefg-----------abcdefg

Fig. 4

Why abcdefg--------------abcdefg（分析）

Our study abcdefg

4、Conclusions

In summary, processing----------abcdefg

Acknowledgments

The authors would like to -----------abcdefg

References

[1]、BergLK, GjønnesJ, HansenV, LiXZ, Knutson-WedelM, WaterlooG, et al. Acta Mater2001;49:3443-51.

[2]、XiaoYP, PanQL, LiWB, LiuXY, HeYB. Mater Des2011;32:2149-56.

Figures

Figure captions

Fig. 1 abcdefg

Fig. 2 abcdefg

Fig. 3 abcdefg

Fig. 4 abcdefg